Yamaha YM2149 Software-Controlled Sound Generator (SSG) ----------------------------------------- Overview The SSG (Software-Controlled Sound Generator) is an NMOS-LSI device designed to be capable of music generation. It only requires the microprocessor or microcomputer (CPU) to initialize its register array, thus reducing the load on the CPU. Music generation is carried out by the three sequence square wave generator, noise generator, and envelope generator according to the set parameters. This allows for the generation of music, special effects, warnings, and various other types of sounds. Features 5V single power supply Easy connection to 8 bit or 16 bit CPU Simple connection to external system through 2 sequence 8 bit I/O port Wide voicing range of 8 octaves Smooth attenuation by 5 bit envelope generator Built-in 5 bit D/A convertor Input of double frequency clock can be handled by built-in clock frequency divider TTL compatible level Low power consumption (typical 125mW) 40 pin plastic DIL package Pin compatible with AY-3-8910 manufactured by GI Pin Layout Vss(GND) 1 40 Vcc(+5V) N.C 2 39 Test1 Analog Channel B 3 38 Analog Channel C Analog Channel A 4 37 DA0 N.C 5 36 DA1 IOB7 6 35 DA2 IOB6 7 34 DA3 IOB5 8 33 DA4 IOB4 9 32 DA5 IOB3 10 31 DA6 IOB2 11 30 DA7 IOB1 12 29 BC1 IOB0 13 28 BC2 IOA7 14 27 BDIR IOA6 15 26 SEL IOA5 16 25 A8 IOA4 17 24 A9 IOA3 18 23 RESET IOA2 19 22 CLOCK IOA1 20 21 IOA0 Block diagram A9 A8 BDIR BC2 BC1 DA7~DA0 o o o o o | | | | | | | | | | | | | | | --- Bus Control ---o Bidirectional -----o I/O Port A <=> IOA7~IOA0 | | | Decoder o--- buffer | | | | o | | | | | | | | o o | Register Addr --o Address --o Register o-------| Latch Decoder Array -----o I/O Port B <=> IOB7~IOB0 o | -------------------------------------- | | | | | o o | o o Noise Music | Envelope Level Frequency Generator Generator | Generator --o Control o----- divider ---o CLOCK | | | | master | | o | | clock | -------o Mixer o-- | ---------o SEL | | | | o | D/A Convertor o------------------ | | | | | | Analog Channel o o o A B C Description of pins 1. DA7 ~ DA0 This is an 8 bit bidirectional data bus which is used for moving data and addresses between the SSG and CPU. In the read and write modes, DA7 ~ DA0 corresponds to B7 ~ B0 of the register array. In the address mode, DA3 ~ DA0 is used for the register address, and DA7 ~ DA4 is used together with A9 and A8 for the upper address. 2. A8 and A9 These are the upper address input pins. A8 has pullup resistance while A9 has pulldown resistance. When the voltage level at A8 while the level at A9 and DA7 ~ DA4 is low, the address mode is selected allowing for the fetching of a register address. Connect A8 and A9 to +5V and ground respectively when not in use. 3. RESET Reset is effective when the voltage level is low, and the contents of all registers in the array are reset to '0'. This pin has pullup resistance. 4. CLOCK Supplies the master clock to the sound generator and envelope generator. This is equipped with a 1/2 frequency divider which allows for the use of a frequency which is 1/2 of the input clock, as the master clock. 5. SEL When SEL is driven to the high level, the input clock is taken as the master clock. When the voltage level of SEL is low, the input clock is divided by 2 to obtain the master clock. This pin has pullup resistance, allowing for full pin compatibility with the AY-3-8910 manufactured by AI, when this pin is not connected to anything. 6. BDIR,BC1 and BC2 Controls the external bus (DA7 ~ DA0) and internal bus of the SSG. The following four modes can be set by the bus control decoder. The bus control is redundant, control is possible even when BC5 is connected to +5V. BDIR BC2 BC1 Mode 0 0 0 Inactive 0 0 1 Address 0 1 0 Inactive 0 1 1 Read 1 0 0 Address 1 0 1 Inactive 1 1 0 Write 1 1 1 Address Inactive mode: DA7 ~ DA0 has high impedance. Address mode: DA7 ~ DA0 set to input mode, and address is fetched from register array. Write mode: DA7 ~ DA0 set to input mode, and data is written to register currently being addressed. Read mode: DA7 ~ DA0 set to output mode, and contents of register currently being addressed are output. 7. ANALOG CHANNEL A,B,C Each of the three channels is equipped with a D/A convertor which converts the calculated digital values to analog signals for output. 8. IOA7 ~ IOA0, IOB7 ~ IOB0 These are two 8 bit I/O ports. These ports allow the SSG to be placed between an external system and the CPU for the transfer of data. These pins have pullup resistance. 9. TEST1 Output pin for testing the device. Do not connect to anything. 10. Vcc +5V power pin. 11. Vss Ground pin. Description of funtions All functions of the SSG are controlled by the 16 internal registers. The CPU need only write data to the internal registers of the SSG. The SSG itself generates the sound. Sound is generated by the following blocks: Music generator: Square waves having a different frequency are generated for each channel (A,B and C) Noise generator: Pseudo-random waveforms are generated (variable frequency) Mixer: Music and noise output are mixed for the three channels (A,B and C) Level control: Constant level or variable level is given for each of the three channels (A,B and C). Constant levels are controlled by the CPU, and variable levels by the envelope generator. Envelope generator: Generates various types of attenuation (single burst attenuated and repeated attenuation) D/A convertor: Sound is output on each of the three channels (A,B and C) at the level determined by the level control. The CPU can read the contents of the internal registers with no effect on sound. Register Array A9 A8 DA7 DA6 DA5 DA4 DA3 DA2 DA1 DA0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 1 1 1 \______________________/\_____________/ Upper addresses Lower addresses (chip select) (register select) Of the ten bit address, the lower addresses DA3 ~ DA0 are used to select the 16 internal registers(register array). The upper addresses are used for chip selection. A9 and A8 is programmed to 01 while DA7 through DA4 are set to 0000. When the upper addresses match this program in the address mode, a register address (lower four bits DA3 through DA0) is fetched from the register address latch. When the value set is in the upper addresses is different from the program value, the bidirectional bus formed from DA7 through DA0 is driven to high impedance. A register address which has been fetched is retained until the next address is fetched, and is not affected by the read, write, or inactive mode. Register Array B7....B0 R0 Frequency of Channel A 00000000 8 bit fine tone adjustment R1 ----0000 4 bit rough tone adjustment R2 Frequency of Channel B 00000000 8 bit fine tone adjustment R3 ----0000 4 bit rough tone adjustment R4 Frequency of Channel C 00000000 8 bit fine tone adjustment R5 ----0000 4 bit rough tone adjustment R6 Frequency of Noise ---00000 5 bit noise frequency R7 I/O port and mixer iinnnttt i-I/O, n-Noise, t-Tone settings bacbacba R8 Level of channel A ---mllll m-Mode, l-Level R9 Level of channel B ---mllll m-Mode, l-Level RA Level of channel C ---mllll m-Mode, l-Level RB Frequency of envelope 00000000 8 bit fine adjustment RC 00000000 8 bit rough adjustment RD Shape of envelope ----cath c-Cont, a-Att, t-Alt, h-Hold RE Data of I/O port A 00000000 8 bit data RF Data of I/O port B 00000000 8 bit data (1) Setting of music frequency (controlled by registers R0 ~ R5) The frequencies of the square wave generated by the music generators for the three channels (A,B and C) are controlled by registers R0 through R5. R0 and R1 control channel A, R2 and R3 are used for channel B, and R4 and R5 control channel C. The oscillation frequency fT is obtained in the following manner from the value of the register TP(decimal). fT = fMaster ------- 16TP fMaster is the frequency of the master clock (this is the input click frequency when SEL is high, and 1/2 of this frequency when low). Rough tone adjustment Fine tone adjustment register Channel register R1 A R0 R3 B R2 R5 C R4 B7 B6 B5 B4 B3 B2 B1 B0 B7 B6 B5 B4 B3 B2 B1 B0 \---------/| \ / Not used | \ / | | TP11 TP10 TP9 TP8 TP7 TP6 TP5 TP4 TP3 TP2 TP1 TP0 12 bit oscillation frequency setting value (TP) (2) Setting of noise generator (controlled by register R6) The noise frequency fN is obtained from the register value NP(decimal) in the following manner. fN = fMaster (fMaster if the frequency of the master clock) ------- 16NP Noise frequency register R6 B7 B6 B5 B4 B3 B2 B1 B0 \------/| \ Not used| \ | | NP4 NP3 NP2 NP1 NP0 5 bit noise frequency setting value (NP) (3) Settings of mixer and I/O ports (controlled by register R7) The mixer is used to combine music and noise components. The combination is determined by bits B5 ~ B0 of register R7. Sound is output when a '0' is written to the register. Thus, when both the noise and tone are '0', the output is combined by the mixer. When the noise is '0' and the tone is '1', only the noise signal is output. When the noise is '1' and the tone is '0', music (square wave) is output. Nothing is output when both the noise and tone are '1'. Selection of input/output for the I/O ports is determined by bits B7 and B6 of register R7. Input is selected when '0' is written to the register bits. I/O port and mixer setting register R7 B7 B6 B5 B4 B3 B2 B1 B0 / /| |\ \ / / | | \ \ I/O Noise Tone B A C B A C B A (Input is selected for I/O port when '0', and noise or tone can be output when '0') (4) Level control (controlled by R8 ~ RA) The audio level output from the D/A convertors for the three channels (A,B and C) is adjusted by registers R8, R9 and RA. Level setting registers Channel R8 A R9 B RA C B7 B6 B5 B4 B3 B2 B1 B0 \------/| |\ \ Not used| | \ \ | | \ \ M L3 L2 L1 L0 Mode 4 bit level selection Mode M selects whether the level is fixed (when M=0) or variable (M=1). When M=0, level is determined from one of 16 by level selection signals L3,L2,L1 and L0 which compromise the lower four bits. When M=1, the level is determined by the 5 bit output of E4,E3,E2,E1 and E0 of the envelope generator of the SSG. (This level is variable as E4 ~ E0 change over time) (5) Setting of envelope frequency (controlled by R8 and RC) Thus, the envelope repetition frequency fE is obtained as follows from the envelope setting period value EP (decimal): fE = fMaster (fMaster if the frequency of the master clock) ------- 256EP Envelope rough adjustment register RC Envelope fine adjustment register RB B7 B6 B5 B4 B3 B2 B1 B0 B7 B6 B5 B4 B3 B2 B1 B0 / \ / \ / \ / \ / | \ EP15 EP14 EP13 EP12 EP11 EP10 EP9 EP8 EP7 EP6 EP5 EP4 EP3 EP2 EP1 EP0 16 bit envelope period setting value (EP) The period of the actual frequency fEA used for the envelope generated is 1/32 of the envelope repetition period (1/fE). (6) Envelope shape control (controlled by RD) The envelope generator counts the envelope clock fEA 32 times for each envelope pattern cycle. The envelope level is determined by the 5 bit output (E4 ~ E0) of the counter. The shape of the envelope is created by increasing, decreasing, stopping, or repeating this counter. The shape is controlled by bits B3 ~ B0 of the register RD. Envelope shape control register RD B7 B6 B5 B4 B3 B2 B1 B0 \----------/ | | | | Not used | | | --- Hold | | ------ Alt | --------- Att ------------ Cont Envelope shape control signals The envelope can take the shapes shown below according to combinations of the CONT, ATT, ALT and HOLD signals. B3 B2 B1 B0 CONT ATT ALT HOLD 0 0 x x \ \--------------------- 0 1 x x /| / |-------------------- 1 0 0 0 \ |\ |\ |\ |\ |\ |\ |\ \| \| \| \| \| \| \| \ 1 0 0 1 \ \--------------------- 1 0 1 0 \ /\ /\ /\ /\ /\ / \/ \/ \/ \/ \/ \/ 1 0 1 1 \ |-------------------- \| 1 1 0 0 /| /| /| /| /| /| /| / / |/ |/ |/ |/ |/ |/ |/ 1 1 0 1 /--------------------- / 1 1 1 0 /\ /\ /\ /\ /\ /\ / \/ \/ \/ \/ \/ \ 1 1 1 1 /| / |-------------------- NOTE - The writing to register RD will reset the envelope frequency clock